Pool Equipment Repairs in Keller, TX
Fort Worth PoolSmiths repairs pumps, filters, heaters, salt systems, and automation for Keller homeowners. Mature trees and established landscaping mean leaf drop, pollen, and organic debris wear pool gear faster here, and our crew knows what to look for on pads across Marshall Ridge, Wildwood, and Preserve at Hidden Lakes.
Pool Equipment We Fix Across Keller
Leaf drop, pollen, and hard water hit Keller pads harder than most. We repair every piece on the equipment pad, from the pump to the automation controller, so you have one crew for the whole system.
Pool Pump Repair
Keller's mature trees drop leaves and pollen that pack skimmer baskets and clog pump impellers. We clear the blockage, replace worn seals and bearings, and restore flow before the motor overheats from the strain.
Pool Filter Repair
Organic debris from established Keller landscaping breaks down inside the filter and fouls the media. We break down the tank, clean or replace the grids and cartridges, and verify the pressure gauge reads true so the filter catches what it should.
Pool Heater Repair
When a Keller heater throws a code or will not hold temperature, we trace it to the flame sensor, the igniter, or the high-limit switch. We also check the gas pressure and the venting so the unit fires reliably through the cooler months.
Automation Repair
Keller pools often run older automation that loses its schedule or drops the Wi-Fi link. We re-pair the controller, rebuild the programs, and check the valve actuators so the pump, heater, and lights run on their own again.
Salt System Repair
Salt cells in Keller scale up from hard fill water and from the organic load that mature trees add. We acid-clean the cell, test the output, and read the control board codes. If the cell is spent, we size a replacement and recalibrate.
Pool Light Repair
A dead or flickering pool light is usually a failed seal, a corroded socket, or a tripped GFCI. We pull the fixture, replace the bulb or the housing, and reseal the niche so water stays out and the light comes back on safely.
Equipment Brands We Work With
Keller pools run a mix of older and newer equipment from Pentair, Hayward, Jandy, and Zodiac, and each brand wires and programs its pumps, heaters, and automation a little differently. Our team stays current through continuing education on the latest models and firmware, so we pull the right part the first time instead of swapping components until something sticks.
On the pump side we work with IntelliFlo, SuperFlo, and MaxPro variable speed lines, plus the older single speed motors still running on many established Keller pads. For automation we handle IntelliTouch, EasyTouch, OmniLogic, and AquaLink, including the phone apps and remotes. When a part is discontinued, we tell you straight and recommend a current replacement.
For heaters we repair Pentair MasterTemp and Hayward Universal gas units, plus HeatPro and UltraTemp electric heat pumps. Heaters fail in specific ways, and the diagnostic codes point us to the exact sensor, igniter, or board that needs attention. We carry common parts so many Keller repairs finish in a single visit.
For salt systems we service IntelliChlor, AquaRite, and NaturePure cells and control boards. We also install and repair LED lighting from Pentair, Hayward, and Jandy, including color lights and the controllers that run them. Whatever sits on your equipment pad, we have likely seen it and fixed it before.
How an Equipment Repair Visit Works
Three clear steps from diagnosis to a working pool, with a written quote before any work starts.
We Diagnose the Problem
We inspect the equipment, pull diagnostic codes, and test the unit under load to find the exact cause. We explain what is failing and why before we recommend anything.
We Send a Written Quote
You get a clear written quote for the part and the labor, with no pressure to decide on the spot. We answer your questions so you understand the fix and the options.
We Complete & Verify the Repair
Once you approve, we do the repair and run the equipment to confirm it works. We clean up the pad and leave a summary of what we fixed and what to watch for.
Pool Equipment Installation in Keller
When a repair is not the smart move, we install new pool equipment sized to your pool and your pad. That includes variable speed pumps, filters, heaters, salt systems, automation, and lighting from the brands we service every day. We match the equipment to your pool's gallonage and plumbing so it runs efficiently from the first day.
A proper installation also means setting the pump speed, programming the automation, and calibrating the salt cell so the whole system works together. We do not just drop in a box and leave. We commission the equipment, walk you through how to use it, and make sure the pad is clean and up to code before we go.
We also handle equipment pad upgrades when you want to modernize an older Keller setup. Swapping a single speed pump for a variable speed model, adding automation, or converting to a salt system can change how your pool feels and how much energy it uses. We plan the upgrade around your existing plumbing and electrical so there are no surprises.
Every installation starts with a free walkthrough and a written quote. There is no pressure, and no surprise charges get added later. You will know the equipment, the scope, and the timeline before any work begins.
Warning Signs You Need Pool Equipment Repair
Pool equipment usually fails slowly before it stops completely. Catching these signs early can save a motor, a heater, or a pump from a much bigger problem.
- A pump that grinds, whines, or runs louder than it used to
- Low or no water flow at the return jets, even when the pump is on
- Error codes or warning lights on the heater, salt cell, or automation panel
- Water pooling under the equipment pad or visible leaks at the fittings
Repair vs Replace: What We Recommend
We give you an honest read on whether a repair or a replacement makes more sense for your equipment. A worn seal or a single sensor on a newer pump is usually worth fixing, while a motor that has failed twice on a unit near the end of its life often points to a replacement. We look at the age of the equipment, the cost of the part, and how often it has failed before we recommend anything.
When a replacement is the better call, we give a free written quote for the new equipment and the install, and we explain why the repair would cost more in the long run. You always get both options laid out clearly so you can choose what fits your pool and your budget.
Equipment Not Running Right?
Get a free diagnostic visit and a written quote from a crew that fixes it the first time.
Get A Free EstimateNeighborhoods We Serve in Keller
From the tree lined pools in Marshall Ridge to the established pads in Wildwood, we know the pool gear across Keller. Homes in Preserve at Hidden Lakes and Overton Ridge often have older pumps and filters that need regular attention, while newer installs in Providence Grove and Tuscany Keller benefit from consistent upkeep and trained diagnostics.
Other Pool Services in Keller
We are a one-stop shop for all pool needs. Explore the other services our locally owned crew offers across Keller.
Pool Cleaning Services
Weekly cleaning, chemical balancing, and skimming that keeps your water clear and swim-ready.
Learn morePool Installation
New pool builds designed for your yard, your home style, and the way you actually swim.
Learn morePool Renovations
Resurfacing, tile, and full makeovers that bring an older pool back to life.
Learn morePool Equipment Installation
New pumps, heaters, salt systems, and automation installed and set up the right way.
Learn moreCommercial Pool Service
Cleaning, chemistry, and equipment service for HOA, apartment, and community pools.
Learn morePool Equipment Repair FAQ
Common questions from Keller homeowners about pool equipment repairs.
Keller has decades of mature trees, and the leaf drop, pollen, and seed pods find their way into the skimmer and the pump basket faster than in open, newer developments. That organic load packs the impeller and wears the shaft seal. We clear the impeller, replace the seal, and show you how to keep the baskets emptied so the pump does not strain between service visits.
Let's Get Your Equipment Running Again
Call us or request a free estimate. A locally owned crew is ready to help.